newbie at routing !!
Sietse van Zanen
sietse at wizdom.nu
Wed Jun 7 14:45:07 CEST 2006
Well if there are more routers in between, the short answer becomes:
All routers in between the two end points need to know the routes to both end points.
From: netfilter-bounces at lists.netfilter.org on behalf of Diana Asnani
Sent: Wed 07-Jun-06 14:24
To: netfilter at lists.netfilter.org
Subject: RE: newbie at routing !!
no, the VLANs are not connected to the same router...the vlan router for
192.168.206.1 is 192.168.206.14
the router is Cisco...
yes, i will take your valuable advice...
>From: "Sietse van Zanen" <sietse at wizdom.nu>
>To: "Diana Asnani" <sakal_woman at hotmail.com>,
><netfilter at lists.netfilter.org>
>Subject: RE: newbie at routing !!
>Date: Wed, 7 Jun 2006 13:17:14 +0200
>I am very tempted to just shout RTFM here. But then again, I'm already
>pissed at some other people, so let's just go back into friendly mode....
>If your PC has default route set to the VLAN router (192.168.202.14) that
>part is ok
>The VLAN router will then need to know the route to 188.8.131.52/32 for
>the host itself or 184.108.40.206/24 if you need to reach the whole subnet, is
>via 192.168.206.1. I'm assuming both VLAN's are on the same VLAN router.
>I don't know anything about your VLAN router, so I cannot tell you the
>command, but on cisco it will be:
>ip route 220.127.116.11 255.255.255.255 192.168.206.1 (or for subnet ip
>route 18.104.22.168 255.255.255.0 192.168.206.1).
>But if I must give you some real valuable advise, educate yourself. This is
>just part of the very basics of networking.
>From: netfilter-bounces at lists.netfilter.org on behalf of Diana Asnani
>Sent: Wed 07-Jun-06 12:46
>To: netfilter at lists.netfilter.org
>Subject: Re: newbie at routing !!
>thanks for the reply...the gateway for my 192.168.202.1 PC is
>which is the vlan router which enables me to ping the 192.168.206.1 vlan
>address...for the route in the network device control, the destination
>network is 192.168.206.0, the subnet mask 255.255.255.240 and the gateway
>192.168.202.14...this is what i have done so far...i am not too sure on how
>i should configure a default gateway ot static route...
> >From: Vinod Chandran <vinod_chandran at multitech.co.in>
> >To: Diana Asnani <sakal_woman at hotmail.com>
> >Subject: Re: newbie at routing !!
> >Date: Wed, 07 Jun 2006 14:17:47 +0530
> >You need to have a route configured to reach 22.214.171.124/24 network.
> >Check ur routing table
> >May be u need to configure a default gateway or a static route.
> >Vinod C
> >Diana Asnani wrote:
> >>I need help!! My VLAN IP is 192.168.202.1. I can ping another PC with
> >>VLAN IP of 192.168.206.1 but i can't ping the 126.96.36.199 address in
> >>that PC. Am i supposed to do some sort of routing configuration? I am
> >>using FC3 as my OS. What am i supposed to do to ping 188.8.131.52?
> >>Get your mobile ringtones, operator logos and picture messages from MSN
> >>Mobile http://msn.smsfactory.no/
>Find just what you are after with the more precise, more powerful new MSN
>Search. http://search.msn.com.my/ Try it now.
Block pop-up ads with MSN Toolbar. http://toolbar.msn.com.my/
More information about the netfilter